Conrad-Johnson CAV-60 Stereo Control Amplifier: Valve Amplification Without a Line Stage
The Conrad-Johnson CAV-60 is a vacuum-tube stereo control amplifier for listeners who want a single-box valve system with as little circuitry as possible between source and speakers. It does the job of an integrated amplifier, with source selection, volume control and 60 watts per channel, but it leaves out the line stage that an integrated amplifier or preamplifier normally carries. Its triode voltage-gain and phase-inverter stages and its EL34 output stage follow the circuit of Conrad-Johnson’s Classic Sixty-Two power amplifier. Buyers building a compact valve system, or replacing a preamp and power amp pair, get fewer boxes, fewer cables and fewer gain stages in the signal path.
What makes the Conrad-Johnson CAV-60 different from an integrated amplifier?
The Conrad-Johnson CAV-60 is built around a circuit that drops the line stage entirely. A conventional integrated amplifier places a line stage between the volume control and the power amplifier section to add gain and buffering. That stage brings its own colourations. In the CAV-60, the signal reaches the power amplifier’s triode voltage-gain stage without passing through a separate line stage.
This design reflects Conrad-Johnson’s stated philosophy that simple circuits yield the best results. Removing the line stage takes out a full set of active devices and coupling components. The single-chassis layout removes the interconnect, extra connections and ground paths that join a separate preamplifier to a power amplifier. Conrad-Johnson credits this shorter path with the CAV-60’s resolution of dynamic shadings, its imaging and its harmonic tonality. The mechanism is a reduced count of stages, parts and contacts, each of which can add its own small error to the signal.
Which speakers suit its 60 watts per channel?
The Conrad-Johnson CAV-60 is rated at 60 watts per channel RMS with both channels driven into 4 ohms, from 30Hz to 15kHz, at no more than 1.5% total harmonic or intermodulation distortion. The both-channels-driven condition matters. It describes how the amplifier performs when its power supply feeds two loudspeakers at once, which is how it’ll be used.
That power comes from a pair of EL34 pentodes per channel operating in ultra-linear mode. Ultra-linear operation connects each valve’s screen grid to a tap on the output transformer. The result sits between pure triode operation, which gives lower distortion but less power, and full pentode operation, which gives more power but higher distortion. It’s an engineering compromise that lets a pair of EL34s deliver 60 watts with distortion kept in check.
At normal listening levels, the amplifier works well below its rated output. Small-signal distortion measures under 0.1% at mid-band, and frequency response runs from 20Hz to 20kHz within +0/−0.5 dB. Conrad-Johnson publishes its power rating into 4 ohms only, so 4-ohm loudspeakers fall within the published specification. Owners of 8-ohm speakers should confirm the pairing with a Conrad-Johnson dealer. Speakers with higher sensitivity need less of the 60-watt budget to reach a given volume, leaving more headroom for peaks.
Can you connect a turntable and other sources to it?
The Conrad-Johnson CAV-60 is a line-level amplifier with a 100 k Ohm input impedance. That’s a high, easy load for a source component. A high input impedance draws little current from the source’s output stage. CD players, DACs, streamers and valve-output components hold their level and low-frequency extension rather than rolling off into a heavy load.
The front panel shows a two-position input selector, giving two line sources. Conrad-Johnson doesn’t list a phono stage among the CAV-60’s specifications, so a turntable needs an external phono preamplifier connected to one of the line inputs. That phono stage handles the cartridge-specific work, including RIAA equalisation, gain for moving-magnet or moving-coil cartridges, and cartridge loading.
How does the Conrad-Johnson CAV-60 compare with separates and other amplifiers?
The Conrad-Johnson CAV-60 is positioned as an alternative to two common routes: a conventional integrated amplifier with a line stage, or a preamplifier paired with a power amplifier. Within Conrad-Johnson’s range, its audio circuit is closely related to the Classic Sixty-Two power amplifier. A Classic Sixty-Two owner still needs a separate preamplifier for source switching and volume. The CAV-60 builds that control function into the same chassis without adding a line stage.
The CAV-60 suits buyers who want valve amplification from one box, run no more than two line sources, have speakers that match its 60-watt, 4-ohm rating, and value a minimal signal path over flexibility. Separates suit buyers who need more inputs, want a preamplifier with its own phono stage, or plan to upgrade the preamplifier and power amplifier independently. With the CAV-60, any future change to amplification is one decision about one unit.
What should you plan for when installing it?
The Conrad-Johnson CAV-60 is about 44.1 cm wide, 34 cm deep and 16.8 cm tall, and weighs around 19 kg. The shelf or rack has to carry that weight, and the amplifier needs open space above and around it. Valve output stages run hot. Conrad-Johnson’s photographs show the CAV-60 both with its valves exposed and under a perforated cover, so airflow around the chassis shouldn’t be restricted.
Cabling stays simple. With no preamp-to-power-amp link to run, the system needs source interconnects, a pair of speaker cables and a mains lead. The speaker outputs are phase correct, meaning the amplifier doesn’t invert the signal. Connecting positive to positive and negative to negative preserves the recording’s absolute polarity, with no need to reverse speaker leads.
The binding posts are machined from billet brass with rhodium over silver plating, fitted with gold-plated billet brass nuts. Rhodium is a hard, corrosion-resistant metal, so the contact surfaces hold up to repeated cable changes and tightening.
What does long-term ownership of this valve amplifier look like?
The Conrad-Johnson CAV-60 is hand assembled, individually inspected and performance-verified by an experienced audio technician before dispatch. Its vacuum tubes are wear items. Output valves such as the EL34 and the small-signal triodes lose performance with use and need replacing over the amplifier’s life, so owners should treat retubing as a running cost.
How does the power supply affect bass and background noise?
The Conrad-Johnson CAV-60 is fitted with larger-value electrolytic reservoir capacitors in its unregulated power supply. Reservoir capacitors store energy between the charging pulses from the mains. Larger capacitance reduces the ripple voltage left on the supply rails, which lowers hum. A larger reservoir sags less under sustained low-frequency demand, which is the basis for Conrad-Johnson’s claim of improved bass response.
Hum and noise measure 100 dB below rated power output. That low residual matters most with high-sensitivity speakers, which make any hum or hiss audible more readily than less sensitive designs. The reservoir electrolytics are bypassed with polypropylene capacitors, which handle the high-frequency demands that large electrolytics deal with less effectively.
Which parts go into the Conrad-Johnson CAV-60’s circuits?
The Conrad-Johnson CAV-60 is built with precision metal-film resistors throughout its audio circuits and their associated power supplies. Metal-film resistors offer tight tolerances, stable values and low noise. Apart from the large reservoir capacitors, every capacitor in those circuits uses a polypropylene dielectric, a material chosen for low loss, low dielectric absorption and stable behaviour across temperature. In a circuit with so few stages, each component has a larger share of influence on the signal, which is why Conrad-Johnson specifies parts this way throughout the CAV-60.